-- Network Working Group C. Kalbfleisch
-- Request for Comments: 4149 Consultant
-- Category: Standards Track R. Cole
-- JHU/APL
-- D. Romascanu
-- Avaya
-- August 2005-- Definition of Managed Objects for Synthetic Sources for
-- Performance Monitoring AlgorithmsSSPM-MIB DEFINITIONS::=BEGIN
IMPORTSMODULE-IDENTITY,OBJECT-TYPE,Counter32,Integer32,Unsigned32FROM SNMPv2-SMI --[RFC2578]TEXTUAL-CONVENTION,StorageType,TruthValue,RowStatusFROM SNMPv2-TC --[RFC2579]MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF --[RFC2578,-- RFC2579,-- RFC2580]OwnerString, rmon
FROM RMON-MIB --[RFC2819]InetAddressType,InetAddressFROM INET-ADDRESS-MIB --[RFC3291]InterfaceIndexOrZeroFROM IF-MIB --[RFC2863]AppLocalIndex
FROM APM-MIB --[RFC3729]Utf8StringFROM SYSAPPL-MIB;--[RFC2287]sspmMIB MODULE-IDENTITYLAST-UPDATED"200507280000Z"-- July 28, 2005ORGANIZATION"IETF RMON MIB working group"CONTACT-INFO" Carl W. Kalbfleisch
Consultant
E-mail: ietf@kalbfleisch.us
Working group mailing list: rmonmib@ietf.org
To subscribe send email to rmonmib-request@ietf.org"DESCRIPTION"This SSPM MIB module is applicable to probes
implementing Synthetic Source for Performance
Monitoring functions.
Copyright (C) The Internet Society (2005). This version
of this MIB module is part of RFC 4149; see the RFC
itself for full legal notices."-- revision historyREVISION"200507280000Z"-- July 28, 2005DESCRIPTION"The original version of this MIB module,
was published as RFC4149."::={ rmon 28}--
-- Object Identifier Assignments--sspmMIBObjects OBJECTIDENTIFIER::={ sspmMIB 1}sspmMIBNotifications OBJECTIDENTIFIER::={ sspmMIB 2}sspmMIBConformance OBJECTIDENTIFIER::={ sspmMIB 3}---- Textual Conventions--SspmMicroSeconds::=TEXTUAL-CONVENTIONDISPLAY-HINT"d"STATUScurrentDESCRIPTION"A unit of time with resolution of MicroSeconds."SYNTAXUnsigned32SspmClockSource::=TEXTUAL-CONVENTIONDISPLAY-HINT"d"STATUScurrentDESCRIPTION"An indication of the source of the clock as defined by the
NTP specification RFC1305 [RFC1305] definition of stratum:
Stratum (sys.stratum, peer.stratum, pkt.stratum): This is
an integer indicating the stratum of the local clock,
with values defined as follows:
0 unspecified
1 primary reference (e.g., calibrated atomic clock,
radio clock)
2-255 secondary reference (via NTP)."REFERENCE"RFC1305."SYNTAXInteger32(0..255)SspmClockMaxSkew::=TEXTUAL-CONVENTIONDISPLAY-HINT"d"STATUScurrent-- UNITS "Seconds"DESCRIPTION"An indication of the accuracy of the clock as defined by
RFC1305. This variable indicates the maximum offset
error due to skew of the local clock over the
time interval 86400 seconds, in seconds."REFERENCE"RFC1305."SYNTAXInteger32(1..65535)---- sspmGeneral--sspmGeneral OBJECTIDENTIFIER::={ sspmMIBObjects 1}sspmGeneralClockResolution OBJECT-TYPE
SYNTAXSspmMicroSecondsMAX-ACCESSread-onlySTATUScurrent-- UNITS MicrosecondsDESCRIPTION"A read-only variable indicating the resolution
of the measurements possible by this device."::={ sspmGeneral 1}sspmGeneralClockMaxSkew OBJECT-TYPESYNTAXSspmClockMaxSkewMAX-ACCESSread-onlySTATUScurrent-- UNITS SecondsDESCRIPTION"A read-only variable indicating the maximum offset
error due to skew of the local clock over the
time interval 86400 seconds, in seconds."::={ sspmGeneral 2}sspmGeneralClockSource OBJECT-TYPESYNTAXSspmClockSourceMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A read-only variable indicating the source of the clock.
This is provided to allow a user to determine how accurate
the timing mechanism is compared with other devices. This
is needed for the coordination of time values
between probes for one-way measurements."::={ sspmGeneral 3}sspmGeneralMinFrequency OBJECT-TYPESYNTAXSspmMicroSecondsMAX-ACCESSread-only-- units MicroSecondsSTATUScurrentDESCRIPTION"A read-only variable that indicates the devices'
capability for the minimum supported
sspmSourceFrequency. If sspmSourceFrequency is
set to a value lower than the value reported
by this attribute, then the set of sspmSourceFrequency
will fail with an inconsistent value error."::={ sspmGeneral 4}---- sspmCapabilities---- Describes the capabilities of the SSPM device.--sspmCapabilitiesTable OBJECT-TYPESYNTAXSEQUENCEOF SspmCapabilitiesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The table of SSPM capabilities."
::={ sspmGeneral 5}sspmCapabilitiesEntry OBJECT-TYPESYNTAX SspmCapabilitiesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Details about a particular SSPM capability."INDEX{ sspmCapabilitiesInstance }::={ sspmCapabilitiesTable 1}
SspmCapabilitiesEntry ::=SEQUENCE{
sspmCapabilitiesInstance AppLocalIndex}sspmCapabilitiesInstance OBJECT-TYPESYNTAXAppLocalIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates whether SSPM configuration of the corresponding
AppLocalIndex is supported by this device. Generally,
entries in this table are only made by the device when the
configuration of the measurement is available."::={ sspmCapabilitiesEntry 1}--
-- sspmSource---- Contains the details of the source of the-- Synthetic Sources for Performance Monitoring algorithms.-- This information is split into two tables. The first defines-- profiles that can be applied to specific sources in the-- control table.--sspmSource OBJECTIDENTIFIER::={ sspmMIBObjects 2}---- sspmSourceProfileTable-- Defines template profiles for measurements.--sspmSourceProfileTable OBJECT-TYPESYNTAXSEQUENCEOF SspmSourceProfileEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The table of SSPM Source Profiles configured."::={ sspmSource 1}sspmSourceProfileEntry OBJECT-TYPESYNTAX SspmSourceProfileEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION
"Details about a particular SSPM Source Profile
configuration. Entries must exist in this table
in order to be referenced by rows in the
sspmSourceControlTable."INDEX{ sspmSourceProfileInstance }::={ sspmSourceProfileTable 1}
SspmSourceProfileEntry ::=SEQUENCE{
sspmSourceProfileInstance Unsigned32,
sspmSourceProfileType AppLocalIndex,
sspmSourceProfilePacketSize Unsigned32,
sspmSourceProfilePacketFillType INTEGER,
sspmSourceProfilePacketFillValue OCTETSTRING,
sspmSourceProfileTOS Integer32,
sspmSourceProfileFlowLabel Integer32,
sspmSourceProfileLooseSrcRteFill OCTETSTRING,
sspmSourceProfileLooseSrcRteLen Integer32,
sspmSourceProfileTTL Integer32,
sspmSourceProfileNoFrag TruthValue,
sspmSourceProfile8021Tagging Integer32,
sspmSourceProfileUsername Utf8String,
sspmSourceProfilePassword Utf8String,
sspmSourceProfileParameter OCTETSTRING,
sspmSourceProfileOwner OwnerString,
sspmSourceProfileStorageType StorageType,
sspmSourceProfileStatus RowStatus}sspmSourceProfileInstance OBJECT-TYPESYNTAXUnsigned32(1..65535)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An arbitrary index."::={ sspmSourceProfileEntry 1}sspmSourceProfileType OBJECT-TYPESYNTAXAppLocalIndexMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The AppLocalIndex value that uniquely identifies the
measurement per the APM-MIB. In order to create a row
in this table, there must be a corresponding row in the
sspmCapabilitiesTable.
When attempting to set this object, if no
corresponding row exists in the sspmCapabilitiesTable,
then the agent should return a 'badValue' error."::={ sspmSourceProfileEntry 2}sspmSourceProfilePacketSize OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The size of packet to be transmitted in bytes. The
size accounts for all data within the IPv4 or IPv6
payloads, excluding the IP headers, IP header options
and link-level protocol headers.
If the size is set smaller than the minimum allowed
packet size or greater than the maximum allowed
packet size, then the set should fail, and the agent
should return a 'badValue' error."::={ sspmSourceProfileEntry 3}sspmSourceProfilePacketFillType OBJECT-TYPESYNTAXINTEGER{random (1),pattern (2),url(3)
}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates how the packet is filled.
'random' indicates that the packet contains random
data patterns. This is probe and implementation
dependent.
'pattern' indicates that the pattern defined in the
sspmSourceProfilePacketFillValue attribute is used to
fill the packet.
'url' indicates that the value of
sspmSourceProfilePacketFillValue should
contain a URL. The contents of the document
at that URL are retrieved when sspmSourceStatus becomes
active and utilized in the packet. If the attempt to
access that URL fails, then the row status is set to
'notReady', and the set should fail with
'inconsistentValue'. This value must contain a
dereferencable URL of the type 'http:', 'https:', or
'ftp:' only."::={ sspmSourceProfileEntry 4}sspmSourceProfilePacketFillValue OBJECT-TYPESYNTAXOCTETSTRING(SIZE(0..255))MAX-ACCESSread-createSTATUScurrent
DESCRIPTION"The string value with which to fill the packet. If
sspmSourceProfilePacketFillType is set to 'pattern',
then this pattern is repeated until the packet is
sspmSourcePacketSize in bytes. Note that if the
length of the octet string specified for this
value does not divide evenly into the packet
size, then an incomplete last copy of this data
may be copied into the packet. If the value of
sspmSourceProfilePacketFillType is set to 'random', then
this attribute is unused. If the value of the
sspmSourceProfilePacketFillType is set to 'url', then
the URL specified in this attribute is retrieved
and used by the probe. In the case of a URL, this value
must contain a dereferencable URL of the type
'http:', 'https:', or 'ftp:' only."::={ sspmSourceProfileEntry 5}sspmSourceProfileTOS OBJECT-TYPESYNTAXInteger32(0..255)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Represents the TOS field in the IP packet header. The
value of this object defaults to zero if not set."DEFVAL{0}
::={ sspmSourceProfileEntry 6}sspmSourceProfileFlowLabel OBJECT-TYPESYNTAXInteger32(0..1048575)-- 20-bit range (0 to 0xfffff)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used to specify the Flow Label in a IPv6
packet (RFC 2460) to force special handling by the IPv6
routers; e.g., non-default quality-of-service handling.
This object is meaningful only when the object
sspmSourceDestAddressType is IPv6(2).
The value of this object defaults to zero if not set."DEFVAL{0}::={ sspmSourceProfileEntry 7}sspmSourceProfileLooseSrcRteFill OBJECT-TYPESYNTAXOCTETSTRING(SIZE(0..240))MAX-ACCESSread-createSTATUScurrent
DESCRIPTION"In the event that the test should run over a
specific route, the intent is to force the route using the
Loose Source Route option in IPv4 [RFC791] and
IPv6 [RFC2460]. This object contains a
series of IP addresses along the path that would be
put into the loose source route option in the IP header.
The IPv4 addresses are to be listed as 32-bit
address values, and the IPv6 addresses are to be
listed as a string of 128-bit addresses. The
maximum length allowed within the IPv4 source route
option is 63 addresses. To simply account for
IPv6 addresses as well, the maximum length of the
octet string is 240. This allows up to 60
IPv4 addresses or up to 15 IPv6 addresses in the
string."::={ sspmSourceProfileEntry 8}sspmSourceProfileLooseSrcRteLen OBJECT-TYPESYNTAXInteger32(0..240)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"In the event that the test should run over a
specific route, the intent is to force the route.
This attribute specifies the length of data to
be copied from the sspmSourceProfileLooseSrcRteFill
into the route data fields of the loose source route
options in the IPv4 or IPv6 headers."::={ sspmSourceProfileEntry 9}sspmSourceProfileTTL OBJECT-TYPESYNTAXInteger32(1..255)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"If non-zero, this specifies the value to place into
the TTL field on transmission."::={ sspmSourceProfileEntry 10}sspmSourceProfileNoFrag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"When true, the 'Don't Fragment Bit' should be set
on the packet header."::={ sspmSourceProfileEntry 11}sspmSourceProfile8021Tagging OBJECT-TYPESYNTAXInteger32(-1..65535)
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"IEEE 802.1Q tagging used in IEEE 802.1D bridged
environments.
A value of -1 indicates that the packets are untagged.
A value of 0 to 65535 is the value of the tag to be
inserted in the tagged packets.
Note that according to IEEE 802.1Q, VLAN-ID tags with
a value of 4095 shall not be transmitted on the wire.
As the VLAN-ID is encoded in the 12 least significant
bits on the tag, values that translate in a binary
representation of all 1's in the last 12 bits
SHALL NOT be configured. In this case, the set should
fail, and return an error-status of 'inconsistentValue'."::={ sspmSourceProfileEntry 12}sspmSourceProfileUsername OBJECT-TYPESYNTAXUtf8StringMAX-ACCESSread-createSTATUScurrentDESCRIPTION"An optional username used by the application protocol."::={ sspmSourceProfileEntry 13}sspmSourceProfilePassword OBJECT-TYPESYNTAXUtf8String
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"An optional password used by the application protocol."::={ sspmSourceProfileEntry 14}sspmSourceProfileParameter OBJECT-TYPESYNTAXOCTETSTRING(SIZE(0..65535))MAX-ACCESSread-createSTATUScurrentDESCRIPTION"An optional parameter used by the application protocol.
For DNS, this would be the hostname or IP. For HTTP,
this would be the URL. For nntp, this would be the
news group. For TCP, this would be the port number.
For SMTP, this would be the recipient (and could
assume the message is predefined)."::={ sspmSourceProfileEntry 15}sspmSourceProfileOwner OBJECT-TYPESYNTAXOwnerStringMAX-ACCESSread-createSTATUScurrentDESCRIPTION
"Name of the management station/application that
set up the profile."::={ sspmSourceProfileEntry 16}sspmSourceProfileStorageType OBJECT-TYPESYNTAXStorageTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The storage type of this sspmSourceProfileEntry. If the
value of this object is 'permanent', no objects in this row
need to be writable."::={ sspmSourceProfileEntry 17}sspmSourceProfileStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Status of this profile.
An entry may not exist in the active state unless all
objects in the entry have an appropriate value.
Once this object is set to active(1), no objects in the
sspmSourceProfileTable can be changed."::={ sspmSourceProfileEntry 18}---- sspmSourceControlTable-- Defines specific measurement instances based on template
-- profiles in the sspmSourceProfileTable which must be-- pre-configured.--sspmSourceControlTable OBJECT-TYPESYNTAXSEQUENCEOF SspmSourceControlEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The table of SSPM measurements configured."::={ sspmSource 2}sspmSourceControlEntry OBJECT-TYPESYNTAX SspmSourceControlEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Details about a particular SSPM configuration."INDEX{ sspmSourceControlInstance }::={ sspmSourceControlTable 1}
SspmSourceControlEntry ::=SEQUENCE{
sspmSourceControlInstance Unsigned32,
sspmSourceControlProfile Integer32,
sspmSourceControlSrc InterfaceIndexOrZero,
sspmSourceControlDestAddrType InetAddressType,
sspmSourceControlDestAddr InetAddress,
sspmSourceControlEnabled TruthValue,
sspmSourceControlTimeOut SspmMicroSeconds,
sspmSourceControlSamplingDist INTEGER,
sspmSourceControlFrequency SspmMicroSeconds,
sspmSourceControlFirstSeqNum Unsigned32,
sspmSourceControlLastSeqNum Unsigned32,
sspmSourceControlOwner OwnerString,
sspmSourceControlStorageType StorageType,
sspmSourceControlStatus RowStatus}sspmSourceControlInstance OBJECT-TYPESYNTAXUnsigned32(1..65535)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An arbitrary index."::={ sspmSourceControlEntry 1}
sspmSourceControlProfile OBJECT-TYPESYNTAXInteger32(1..65535)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"A pointer to the profile (sspmSourceProfileEntry) that
this control entry uses to define the test being
performed."::={ sspmSourceControlEntry 2}sspmSourceControlSrc OBJECT-TYPESYNTAXInterfaceIndexOrZeroMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The ifIndex where the packet should originate from the
probe (if it matters). A value of zero indicates that
it does not matter and that the device decides."::={ sspmSourceControlEntry 3}sspmSourceControlDestAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-createSTATUScurrent
DESCRIPTION"The type of Internet address by which the destination
is accessed."::={ sspmSourceControlEntry 4}sspmSourceControlDestAddr OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The Internet address for the destination. The formatting
of this object is controlled by the
sspmSourceControlDestAddrType object above.
When this object contains a DNS name, then the name is
resolved to an address each time measurement is to be made.
Further, the agent should not cache this address,
but instead should perform the resolution prior to each
measurement."::={ sspmSourceControlEntry 5}sspmSourceControlEnabled OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"When set to 'true', this test is enabled. When set to
'false', it is disabled."::={ sspmSourceControlEntry 6}
sspmSourceControlTimeOut OBJECT-TYPESYNTAXSspmMicroSecondsMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Timeout value for the measurement response. If no
response is received in the time specified, then
the test fails."::={ sspmSourceControlEntry 7}sspmSourceControlSamplingDist OBJECT-TYPESYNTAXINTEGER{deterministic(1),poisson(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"When this attribute is set to 'deterministic', then
packets are generated at with a fixed inter-packet
injection time specified by sspmSourceFrequency.
When this attribute is set to 'Poisson', then packets
are generated with inter-packet injection times sampled
from an exponential distribution with the single
distributional parameter determined by the inverse
frequency)."::={ sspmSourceControlEntry 8}sspmSourceControlFrequency OBJECT-TYPESYNTAXSspmMicroSecondsMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The inverse of this value is the rate at which packets
are generated. Refer to sspmSourceSamplingDistribution.
If the value set is less than the value of
sspmGeneralMinFrequency, then the set will fail with an
error-status of 'inconsistentValue'."::={ sspmSourceControlEntry 9}sspmSourceControlFirstSeqNum OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The first sequence number of packets to be transmitted."::={ sspmSourceControlEntry 10}sspmSourceControlLastSeqNum OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-only
STATUScurrentDESCRIPTION"The last sequence number transmitted. This value is updated
by the agent after packet generation."::={ sspmSourceControlEntry 11}sspmSourceControlOwner OBJECT-TYPESYNTAXOwnerStringMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Name of the management station/application that set
up the test."::={ sspmSourceControlEntry 12}sspmSourceControlStorageType OBJECT-TYPESYNTAXStorageTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The storage type of this sspmSourceControlEntry. If the
value of this object is 'permanent', no objects in this row
need to be writable."::={ sspmSourceControlEntry 13}sspmSourceControlStatus OBJECT-TYPESYNTAXRowStatus
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Status of this source control entry.
An entry may not exist in the active state unless all
objects in the entry have an appropriate value.
When this attribute has the value of
'active', none of the read-write or read-create attributes
in this table may be modified, with the exception of
sspmSourceControlEnabled."::={ sspmSourceControlEntry 14}---- sspmSinkTable---- Contains attributes for configuration of Synthetic-- Sources for Performance Monitoring sinks, i.e.,-- sinks for receipt of one-way delay measurements.--sspmSink OBJECTIDENTIFIER::={ sspmMIBObjects 5}sspmSinkTable OBJECT-TYPESYNTAXSEQUENCEOF SspmSinkEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table configuring the sink for measurements."::={ sspmSink 1}
sspmSinkEntry OBJECT-TYPESYNTAX SspmSinkEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The details of a particular sink entry. If the measurement
is a round-trip type, then the sink entry will be on the
same probe as the corresponding sspmSourceEntry. If the
measurement is a one-way, type then the sink entry will be
on a different probe."INDEX{ sspmSinkInstance }::={ sspmSinkTable 1}
SspmSinkEntry ::=SEQUENCE{
sspmSinkInstance Unsigned32,
sspmSinkType AppLocalIndex,
sspmSinkSourceAddressType InetAddressType,
sspmSinkSourceAddress InetAddress,
sspmSinkExpectedRate SspmMicroSeconds,
sspmSinkEnable TruthValue,
sspmSinkExpectedFirstSequenceNum Unsigned32,
sspmSinkLastSequenceNumber Unsigned32,
sspmSinkLastSequenceInvalid Counter32,
sspmSinkStorageType StorageType,
sspmSinkStatus RowStatus}sspmSinkInstance OBJECT-TYPESYNTAXUnsigned32(1..65535)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An index. When the measurement is for a round-trip
measurement, then this table entry is on the same probe as
the corresponding sspmSourceEntry, and the value of this
attribute should correspond to the value of
sspmSourceInstance. Management applications configuring
sinks for one-way measurements could define some
scheme whereby the sspmSinkInstance is unique across
all probes. Note that the unique key to this entry is
also constructed with sspmSinkType,
sspmSinkSourceAddressType, and sspmSinkSourceAddress.
To make the implementation simpler, those other
attributes are not included in the index but uniqueness
is still needed to receive all the packets."::={ sspmSinkEntry 1}
sspmSinkType OBJECT-TYPESYNTAXAppLocalIndexMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The AppLocalIndex value that uniquely identifies the
measurement per the APM-MIB. In order to create a row
in this table, there must be a corresponding row in the
sspmCapabilitiesTable. If there is no corresponding
row in the sspmCapabilitiestable, then the agent will
return an error-status of 'inconsistentValue'."::={ sspmSinkEntry 2}sspmSinkSourceAddressType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The type of Internet address of the source."::={ sspmSinkEntry 3}sspmSinkSourceAddress OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The Internet address of the source. The formatting
of this object is controlled by the sspmSinkSourceAddressType
object above.
This object should be set only to a valid device address
that has been administratively configured into the
device. If a set attempts to set this object to an
address that does not belong (i.e., is not administratively
configured into the device), the set should fail, and the
agent should return a error-status of 'inconsistentValue'."::={ sspmSinkEntry 4}sspmSinkExpectedRate OBJECT-TYPESYNTAXSspmMicroSecondsMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The expected rate at which packets will arrive."::={ sspmSinkEntry 5}sspmSinkEnable OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates if the sink is enabled or not."::={ sspmSinkEntry 6}sspmSinkExpectedFirstSequenceNum OBJECT-TYPE
SYNTAXUnsigned32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The expected first sequence number of packets.
This is used by the sink to determine if packets
were lost at the initiation of the test."::={ sspmSinkEntry 7}sspmSinkLastSequenceNumber OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last sequence number received."::={ sspmSinkEntry 8}sspmSinkLastSequenceInvalid OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of packets that arrived whose
sequence number was not one plus the value of
sspmSinkLastSequenceNumber."::={ sspmSinkEntry 9}
sspmSinkStorageType OBJECT-TYPESYNTAXStorageTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The storage type of this sspmSinkEntry. If the value
of this object is 'permanent', no objects in this row
need to be writable."::={ sspmSinkEntry 10}sspmSinkStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Status of this conceptual row.
An entry may not exist in the active state unless all
objects in the entry have an appropriate value.
Once this object is set to active(1), no objects with
MAX-ACCESS of read-create in the sspmSinkTable can
be changed."::={ sspmSinkEntry 11}---- Notifications------ Conformance information--sspmCompliances OBJECTIDENTIFIER::={ sspmMIBConformance 1}
sspmGroups OBJECTIDENTIFIER::={ sspmMIBConformance 2}-- Compliance StatementssspmGeneralCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"A general compliance that allows all things to be optional."MODULE-- this moduleMANDATORY-GROUPS{ sspmGeneralGroup }GROUP sspmSourceGroup
DESCRIPTION"The SSPM Source Group is optional."GROUP sspmSinkGroup
DESCRIPTION"The SSPM Sink Group is optional."GROUP sspmUserPassGroup
DESCRIPTION"The SSPM User Pass Group is optional."::={ sspmCompliances 1}---- SSPM Source Compliance--sspmSourceFullCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"A source compliance. Use this compliance when implementing
a traffic-source-only device. This is useful for implementing
devices that probe other devices for intrusive application
monitoring. It is also useful for implementing the source
of one-way tests used with a sink-only device."MODULE-- this moduleMANDATORY-GROUPS{ sspmGeneralGroup, sspmSourceGroup }GROUP sspmUserPassGroup
DESCRIPTION"The SSPM User Pass Group is optional."::={ sspmCompliances 2}---- SSPM Sink Compliance--sspmSinkFullCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"A sink-only compliance. Use this compliance when implementing a
sink-only device. This is useful for devices to receive one-way
measurements."MODULE-- this moduleMANDATORY-GROUPS{ sspmGeneralGroup, sspmSinkGroup }::={ sspmCompliances 3}---- Groups--sspmGeneralGroup OBJECT-GROUP
OBJECTS{
sspmGeneralClockResolution,
sspmGeneralClockMaxSkew,
sspmGeneralClockSource,
sspmGeneralMinFrequency,
sspmCapabilitiesInstance
}STATUScurrentDESCRIPTION"The objects in the SSPM General Group."::={ sspmGroups 1}sspmSourceGroup OBJECT-GROUPOBJECTS{
sspmSourceProfileType,
sspmSourceProfilePacketSize,
sspmSourceProfilePacketFillType,
sspmSourceProfilePacketFillValue,
sspmSourceProfileTOS,
sspmSourceProfileFlowLabel,
sspmSourceProfileLooseSrcRteFill,
sspmSourceProfileLooseSrcRteLen,
sspmSourceProfileTTL,
sspmSourceProfileNoFrag,
sspmSourceProfile8021Tagging,
sspmSourceProfileUsername,
sspmSourceProfilePassword,
sspmSourceProfileParameter,
sspmSourceProfileOwner,
sspmSourceProfileStorageType,
sspmSourceProfileStatus,
sspmSourceControlProfile,
sspmSourceControlSrc,
sspmSourceControlDestAddrType,
sspmSourceControlDestAddr,
sspmSourceControlEnabled,
sspmSourceControlTimeOut,
sspmSourceControlSamplingDist,
sspmSourceControlFrequency,
sspmSourceControlFirstSeqNum,
sspmSourceControlLastSeqNum,
sspmSourceControlOwner,
sspmSourceControlStorageType,
sspmSourceControlStatus
}STATUScurrentDESCRIPTION"The objects in the SSPM Source Group."::={ sspmGroups 2}sspmUserPassGroup OBJECT-GROUPOBJECTS{
sspmSourceProfileUsername,
sspmSourceProfilePassword
}STATUScurrentDESCRIPTION"The objects in the SSPM Username and password group."::={ sspmGroups 3}sspmSinkGroup OBJECT-GROUPOBJECTS{
sspmSinkType,
sspmSinkSourceAddressType,
sspmSinkSourceAddress,
sspmSinkExpectedRate,
sspmSinkEnable,
sspmSinkExpectedFirstSequenceNum,
sspmSinkLastSequenceNumber,
sspmSinkLastSequenceInvalid,
sspmSinkStorageType,
sspmSinkStatus
}STATUScurrentDESCRIPTION"The objects in the SSPM Sink Group."::={ sspmGroups 4}END